ASHRAE 33-2000 PDF

Operations Manual, Section 4, STEP , Applicants shall submit the following documentation to. AHRI: •. Coil physical data per ASHRAE 33 (refer to Section );. ASHRAE Methods Of Testing Forced Circulation Air Cooling And Air Heating Coils. Be notified when this Standard is updated or amended – Add to. ANSI/ASHRAE Standard (Supersedes ANSI/ASHRAE Standard ) Methods of Testing Forced-Circulation Air-Cooling and Air-Heating Coils.

Author: Gujora Kazirn
Country: Cuba
Language: English (Spanish)
Genre: Music
Published (Last): 18 December 2017
Pages: 229
PDF File Size: 12.10 Mb
ePub File Size: 13.86 Mb
ISBN: 853-8-76016-979-9
Downloads: 68232
Price: Free* [*Free Regsitration Required]
Uploader: Vigor

Hot wire anemometer d. Vallort, CO James W.

Numerous studies conclude that the deter- B5. If necessary, the mixing chamber shall contain deflectors or vanes to azhrae the airstream to an extent that air temperatures in the plane of measurement do not vary more than 1. Calculations, and Pressure Drop Calculations See Dimension H, Figure 3. We need your help!

Moore, John fice Flowmeters. Through its Handbook, appropriate chapters will contain up-to-date Standards and design considerations as the material is systematically revised. An alternative to this fluid flow rate calculation method is that fluid flow rates may be asjrae directly from the applicable flowmeter calibration chart supplied by the flowmeter manufacturer.

For ashrrae inlet chambers, the hydraulic diameter, Dcis equal to four times the crosssectional area divided by the chamber perimeter.

This foreword is not part of this standard.

Static pressure taps may be made with piezometer rings annulus or by manifolding 3 or 4 taps together with tubing. A manually operated expansion valve.

Liquid mass flowmeter intake chamber cross-sectional area. The measured pressure drop per this standard will be determined by using static pressure taps external to the unit in upstream and downstream piping. Help Center Find new research papers in: Leaving air enthalpy at coil: This is a normative annex and is part of the standard.

Related PDF:  RCCG DIGGING DEEP PDF

ASHRAE – Free Download PDF

The condensate level shall be the mixing section is not below 0. Static pressure tap construction annulus, braze joints, tubing, etc. Suitable insulation having an RSI of 0. A minimum of 10 pipe inside diameters downstream of an elbow, mitered bend, or tee in the suction header to deter- a.

Sight glasses located immediately before and after the the variations over this range. Determine wr from the flowmeter calibration chart supplied by the flowmeter manufacturer. The suction temperature shall be taken as the average of the recorded readings. Every effort is made to balance the concerned interests on all Project Committees. To minimize possible temperature stratification, appro- located below the outlet. The con- tank having sufficient capacity to accumulate the flow for at necting pipes shall be the same size as the coil supply and least two minutes and shall be located so that the liquid leav- return connections.

Single-phase liquid pressure drop through entering coil conducting the following test and comparing the measure- and leaving coil pressure measurement pipes, kPa [psi] ments to calculated adjustment values.

The uniformity of ashrqe velocity of the air entering the coil shall be initially determined by a pitot tube traverse made on the first test run only to prove out the setup, as described in Normative Annex C. The method determines the refrigerant mass flow rate by measuring its change in enthalpy and the heat removed from it on asyrae through the condenser. Instruments shall be recalibrated on a regular schedule that is appropriate for each instrument, and calibration records shall be maintained.

Related PDF:  SIMULATION USING PROMODEL 3RD EDITION EBOOK DOWNLOAD

We need your help to maintenance this website. These provisions shall take into consideration the orientation of pressure taps and manifold connections.

See Dimension L, Figure 3. The average entering wet-bulb air temperature for a dehumidifying coil test shall not vary by more than 0. The temperatures shall be averaged to determine the average air dry-bulb temperature surrounding intake and mixing chambers t5db.

Evaluate the specific heat of the hot glycol solution at constant pressure and temperature at 0. The piping and positioned so that only the specially drilled vent hole loss shall be determined by calibration of the measurement opening is operative during the test. If necessary, the intake chamber shall contain diffusion baffles to ensure uniform air velocity over the face of the coil and uniform temperature as required in Section 9.

Psaverage air humidity ratio Wmand average air dry- bulb temperature tmdb. An equivalent test form may be used provided it contains the information shown on the forms available online.

ASHRAE 33-2016

Describe and specify laboratory test methods and proce- tions of variables being measured remain within stated limits dures. Liquid-vapor mixtures used for air cooling controlled by a thermal expansion valve. The purpose of this annex is to provide a method for ver- C2. A manually controlled ashre expansion valve. If I-P units are used, the immediately preceding item, which applies to SI units, is not required to also be used.